Moisture
Separators, Air Filters, Aftercoolers and Air Dryers
Reduce Maintenance Costs, Down-Time and Wear
on your Pneumatic Machinery and Equipment with Dry Air
Moisture Control
Moisture
in your compressed air is a big problem! It makes the abrasive
in your blast machine damp or wet, causing the abrasive flow
from the machine to be uneven and reduce or even completely
block media flow. The operator may find himself opening the
media valve to get more grit, thus wasting the grit. Moist
abrasive media can adhere to the internal components of the
blaster, and when it dries, it can be extremely difficult
to remove! Water and oil vapors can cause "flash rusting" on
the surface of steel products and oil vapors deposited on
surfaces will cause paint and other coatings to adhere poorly
or create early failures such as chipping and separating.
An uneven or blocked abrasive flow will require
you to use more abrasive, make blasting jobs take longer
and damage your blast equipment!
Compressed
air entering the AirPrep system passes
through a prefilter, removing severe
contaminates, particles, and moisture
before going to the cooler. The air
then enters the lower tank where
it expands and slows down, allowing
the moisture to fall out. Next, air
travels up through a stainless steel
particle filter or deliquescent tablets
into the clean air manifold. The
air is now cooler, cleaner and drier,
with very little drop in pressure.
More
than just a separator, RTi's Patented Eliminex® Separator
/ Filter provides 3
Micron Filtration with very low pressure
drop.
Using
RTi's exclusive, and patented, Inverse-Flow
technologyand a deep
bed of stainless steel mesh media, the RTi Eliminex® Separator
/ Filter eliminates condensed liquids in the main line.
As a result, downstream
dryers and filters perform better and last longer.
The RTi Eliminex Separator / Filter can be installed in
compressor room applications or on branch legs of larger
systems. Units come in ports from 1/2" to 6" flange
models, with flows ranging from 60 SCFM to 5,500 SCFM.
Eliminex
Separator Filter (Metal Bowl)
Weight
(lbs)
Height
(in.)
Width
(in.)
Depth
(in.)
RT1P-175-M04-F
Eliminex
175scfm 1/2" with Auto Drain
7.00
19.00
4.60
4.60
RT1P-175-M06-F
Eliminex
175scfm 3/4" with Auto Drain
7.00
19.00
4.60
4.60
RT1P-175-M08-F
Eliminex
175scfm 1" with Auto Drain
7.00
19.00
4.60
4.60
RT1P-250-M08-F
Eliminex
250scfm, 1" with Auto Drain
7.00
19.00
4.60
4.60
RT1M-300-M10-F
Eliminex
300scfm 1-1/4" with Auto Drain
30.00
33.00
7.80
7.80
RT1M-300-M12-F
Eliminex
300scfm 1-1/2" with Auto Drain
30.00
33.00
7.80
7.80
RT1M-300-M16-F
Eliminex
300scfm 2" with Auto Drain
30.00
33.00
7.80
7.80
* Other Sizes Available
Eliminizer
Application Dryer
Engineered specifically to remove
condensed liquids from air streams
prior to pneumatic applications, the RTi Eliminizer® Application Dryer
is designed with 4
separate modes of filtration in a single housing.
Contaminated
compressed air enters the housing spinning rapidly downward.
This spinning
motion forces contamination to the inside
of the bowl where it drains to the bottom of the bowl.
The air then changes direction from vertically downward
to vertically upward. This flow
inversion further removes contamination
prior to entering the filter element. The now pre-filtered
air is passed through a stainless steel mesh and finally
through a bed of cotton, polyester and stainless steel
material where friction
drying takes place.
Filter / Dryer
Eliminates both water condensates and dirt particulate
at point-of-use applications
99.7% efficiency at 1.0 microns
Extends life of all downstream products
Easy to Service: Long-lasting, spin-on spin-off replacement
elements
Utilizes stainless steel and cotton elements
Eliminizer
Application Dryer Filter (Poly Bowl)
Weight (lbs)
Height
(in.)
Width
(in.)
Depth
(in.)
RT3P-035-P02-F
Eliminizer,
35scfm, 1/4" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-035-P03-F
Eliminizer,
35scfm, 3/8" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-035-P04-F
Eliminizer,
35scfm, 1/2" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-060-P02-F
Eliminizer
60scfm, 1/4" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-060-P03-F
Eliminizer
60scfm, 3/8" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-060-P04-F
Eliminizer
60scfm, 1/2" with Auto Drain
3.00
11.50
3.75
3.75
RT3P-090-P04-F
Eliminizer
90scfm, 1/2" with Auto Drain
6.50
15.00
4.50
4.50
RT3P-090-P06-F
Eliminizer
90scfm, 3/4" with Auto Drain
6.50
15.00
4.50
4.50
RT3P-090-P08-F
Eliminizer
90scfm, 1" with Auto Drain
6.50
15.00
4.50
4.50
RT3P-150-PO4-F
Eliminizer
150scfm, 1/2" with Auto Drain
6.50
16.50
4.50
4.50
RT3P-150-P06-F
Eliminizer
150scfm, 3/4" with Auto Drain
6.50
16.50
4.50
4.50
RT3P-150-P08-F
Eliminizer
150scfm, 1" with Auto Drain
6.50
16.50
4.50
4.50
* Other Sizes Available
Schmidt
Axxiom Moisture Separators
Moisture
accumulates in compressed air in vapor form
at the air compressor. The moisture creates
problems when the hot compressed air
is cooled and the vapor condenses into water
droplets. In blast systems, this cooling occurs
in two
primary areas. First, when the air enters
the blast pot where
it expands. Second, as the compressed air
exits the blast nozzle and again it expands.
The expansion cools the air causing condensation
of moisture in the blast media and
on the object being
blasted.
The Schmidt moisture separator allows the
air to
expand inside an ASME coded pressure vessel
where
moisture condenses and is
trapped by the stainless steel coalescing element.
